![]() |
| Pelicans flying in aerodynamic formation |
![]() |
| Lots of boating activity in and out of the marina (the boat docks are just below the tall buildings) |
![]() |
| Back from the bike ride |
![]() |
![]() |
| There's corrosion on the braided steel line for the cold water supply hose to the faucet on one of the sinks in the larger bathroom. |
![]() |
| Like with the small bathroom hot water supply hose, I'm replacing with a non-steel braided line. I'm hoping these will last or not degrade like the steel braided lines... |
![]() |
| This is the faucet wrench to reach the hard to get to connection at the bottom of the faucet. |
![]() |
| After hose replacement... |
![]() |
| There's some pretty bad corrosion on the steel braided line. You would think this would be made of stainless steel that's more corrosion resistant than this... |
![]() |
| Another spot with corrosion |
![]() |
| A couple more spots of corrosion... I'm not sure why certain spots are corroding. Perhaps it's the stress in those areas or there's more of a chance of moisture retention in those spots? |
![]() |
| First loosen the locking nut (on the bottom) |
![]() |
| Only took about a 1/4 turn to loosen |
![]() |
| Then adjust the water pressure. Turning counter-clockwise lowers the pressure, which is my intention |
![]() |
| This view is one side of the fold out trays and part of the main section |
![]() |
| This is a ratcheting tap handle. It's got a small knob at the top that you pull up and rotate to change the ratcheting direction |
![]() |
| I think it says it's made in India... |
![]() |
| This seems to be a T-handle socket tool but it has a section near the bottom that folds out to give leverage. I'm not sure why you need that when you have a handle that's about the same size... |
![]() |
| Starrett hacksaw blades |
![]() |
| This is a "saw set" that lets you angle the teeth on a saw blade to different settings. |
![]() |
| The brand is "Boice" and it appears to be a bore checking gauge |
![]() |
| Add caption |
![]() |
| It was last calibrated about 30 years ago... |
![]() |
| A smaller version of the ratcheting tap handle and a very old 1/4" Craftsman ratchet |
![]() |
| miscellaneous... |
![]() |
| In the main compartment... |
![]() |
![]() |
| Hazet brand special tools (may be for diesel Mercedes engine service) |
![]() |
| Plomb tools on the left... |
![]() |
| Hazet special tools & and a straight reamer on a swivel socket setup. On the right is a MATADOR brand special tool with the Mercedes-Benz logo on it... |
![]() |
| More Hazet special tools... |
![]() |
| Maxwell and Fiat wrenches (there was a car brand "Maxwell" pre-WWII... |
![]() |
| Rolls Royce wrench (says "Don't Hammer") |
![]() |
| RR logo on the wrench |
![]() |
| Hazet special tool wrenches (two of the same) |
![]() |
| Hazet tools have a very nice design/shape and finish... |
![]() |
| The "Hazet" logo is also a very nice graphic design... |
![]() |
| The beach and the jetty are still closed... |
![]() |
| There's been a lot of boating activity in and out of the marina... |
![]() |
| It's surprising that the steel braided line corrodes like this... |
![]() |
| close up |
![]() |
![]() |
| There's very little space to get to the bottom of the faucet. Had to use a special "faucet" wrench to remove & install the line. |
![]() |
| The shut off valve is old but working OK |
![]() |
| Finished |