Thursday, October 29, 2020

Old & Rough Tool Case - part 22 -- Wrong Key...

The keys that don't fit...


The lock is held in the lid with four wood screws.


Using an old wood handle screwdriver to remove the flat slot screws.


The screws were pretty tight but I was able to remove them without damaging the slots in the screws.


This Kennedy toolbox on the back counter has a drawer for screw drivers, where the old screwdriver I used is stored.


This is one of the tools that I "restored" previously.  One of the things I had done was to grind/sand the tips to be flat and sharp.
This tip is in perfect condition & it's exactly the right size for the wood screws.


The lock can now be pulled out of the lid.


There's evidence of how the notch for the lock was made...

The lock has some pretty strong surface corrosion/pitting.


The one key that will go into the lock won't turn.


The tip of the key sticks out the back side of the lock through a very small hole/slot.


The reason the key doesn't turn is because the key is too tall to clear the notch at the top of the key hole.
Basically, it's too big.


Looking into the key slot, there's nothing in the hole in the 12 O'clock position.


This key is also too tall.  There's a notch in the key near the head, that probably interacts with the correct lock that this key is for.


After cleaning the back of the lock a little bit more, a logo is kind of visible toward the bottom of this picture.


The key that goes into the lock has the markings "Eagle Lock Co. Terryville Conn. U.S.A." on it.


The marking on the lock says "N C Co. Rockford" (I think Rockford is in the state if Illinois).  Thus the key and the lock companies don't match...


A closeup of the notch in the lid for the lock.
It shows how the leatherette was trimmed to fit inside the notch.


There's some damage to the lid near the lock, on the outside edge.

 

Car & Driver Magazine -- July 1994


I like the wheel design on this generation of M3.  Would like to find one at a swap meet someday...


Just the fact that they could do a comparison of six wagons is pretty amazing considering that there's almost none left...


The T100 was Toyota's first nearly full size pickup.  Don't see these anymore...


Don't see this generation of Integra anymore...


The concept of a two seater targa is very appealing.  The del Sol design wasn't so attractive...



Hardly ever see a Saturn any more...


Kind of the precursor to CarFax but general review/information on cars...


 

Yard non-sale...

I've seen quite a few people in the neighborhood do this.  They set out a table either on the street or near the sidewalk in front of their house and put out stuff they're giving away for free...
Seems that since they're stuck at home, there's a lot of cleaning/organizing going on...

 

1996 Nissan Pathfinder Brochure






 

Wednesday, October 28, 2020

Old & Rough Tool Case - part 20 -- Applying Danish Oil on the Drawer Fronts

Started by applying to the small drawers...


Enough of the oil is applied, using a cloth, so that there's an even wet look after application


This is one of the small shallow drawers, before the oil is applied.


After oil application.
This oil has a cherry color in it so that it darkens the raw wood...


The oil evens out the color of the oak wood...


Applying the oil on the larger drawers...


All the drawers have been oiled.


After about 30 minutes, the excess oil is wiped with a cloth rag to even out the finish.


All the drawers put back in the case.


The end result is very good.  It looks old and used but not dirty.
There's a slight gloss that will lessen after the oil sets overnight.  The Cherry Color Danish Oil gives the old oak wood a nice warm color.


The overall appearance is pretty even.

Still need to work on the outside of the case, in terms of gluing down the torn & loose leatherette, cleaning & then finding a way to even out the exterior color.
Where there's exposed wood, I'll find a way to color it black.
Don't know if I'll apply paint or ?

I moved the case to the back counter of the garage so that the oil can set/dry overnight.

Also need to do something with all the metal corner protectors and the handle...