Tuesday, October 20, 2020

Old & Rough Tool Case - part 13 -- Vacuuming & Cleaning the Drawer Fronts -- Top Left Drawer

Started with the top left drawer.  It's the one at the top of the picture.
This close-up picture shows how dirty the knobs and drawer front are...

Before vacuuming.  It's not too bad.

After vacuuming.

The bottom is galvanized sheet steel.

There are places where something is on the  surface of the wood.
It's easier to use a blade to scrape it off...

Have to be careful not to cut into the old finish or wood...

Ran out of 409.  Used Simple Green, diluted to 1-to-1 with water.
This is the strongest concentration recommended by the directions...

Started cleaning the knobs and escutcheon using an old kitchen scrubbing sponge.  It works but take a lot of scrubbing...

After cleaning.  Looks presentable.  Still shows the wear and tear over the years...

Knob after cleaning.  Not trying to make is shiny.  Just clean enough to be presentable.  Overall, the case will not be too nice.  There will be places with damage and missing leatherette.  So, I don't want any part of the case to be too nice.  If these knobs are made to shine, then it will contrast too strongly with other parts of the case...
Ultimately, want the case to end up clean but still showing all the damage from many decades of use...

Back of the drawer has "28" in pencil.
28 shows up on all the parts of the case...

After cleaning.  Placed the drawer back in it's place.

Shows the difference after cleaning, versus the other drawers...

 

Tuesday, October 13, 2020 -- Manhattan Beach Pier

In the left of this picture, there's a fully kitted road bike guy on a pretty fancy bike.  It's hard to see in the picture but he's got some of the deepest wheels I've see, outside of a time trial bike.  The rims have to be around 75 mm deep!  Good for going fast but probably not so good in cross-winds...

I passed him on Ballona Creek and he passed me back.  Going at my own pace, I ended up passing him again, just before we got to the beach.  I don't think he liked getting passed back...  He stopped at the pier, like me.
On my way back home, I ended up passing him again.  His ride apparently is similar to mine...

 

1995 BMW 5 series brochure






 

Phil & Enzo - part 21








Monday, October 19, 2020

Old & Rough Tool Case - part 12 -- Cleaning the top of the case (about 1/2 way through)

With the front lid installed & closed, Started cleaning the top of the case.
I don't have a key for the lock so the front lid won't stay in this closed position.  If the case gets tilted, the front lid will swing down...


The fit of the front lid to the case is actually pretty good.



I'm using 409 household cleaner.  Again, amazing amount of dirt on the leatherette...



This is after a lot of wiping with the shop towel...


Started moving across the case...


These initials were completely not visible until the dirt was cleaned.  It was surprising to see these initials appear.  A little bit like magic...
JMR was born in 1900.  If this case was made in 1928 (which is possible due to the design & features on this case), then JMR may have been in his very late 20's when he acquired this case.
JMR passed away in 1979.
As I use this case to store stuff in the future, I'll always think of JMR, even though I've never met him...

 

Monday, October 12, 2020 -- Manhattan Beach Pier & Dockweiler Beach Parking Area

A few people at the pier but nothing like it was on Saturday...

It's a very nice day at the beach (low 70's).



This is the parking lot at Dockweiler beach where I usually cut across from the bike path to the parking lot service road.
Some people apparently spent a lot of money on some tires...

This is where I usually ride up and turn left to go along the parking service road.  The construction is ongoing on the road above the bluffs...