Wednesday, April 22, 2020
Kids made flan - the day after (it had sat in the fridge for about 24 hours)
 |
| Turned out better after 24 hours. Tasted really good. |
Tuesday, April 21, 2020
Rear Brake Pad on the Bike -- Came loose on the ride back from the Marina Del Rey Bike Path Bridge...
 |
| About half way back home, on my ride to the Marina Del Rey bike path bridge, the bike suddenly started slowing-braking. I stopped and found that the right side brake pad on the rear brake caliper had come loose and was jamming against the wheel. Using the compact tool set I carry in my under seat bag, I was able to reinstall the pad to fix it and get back home. During the repair on the side of the bike path, as I tightened the pad back in position, a piece of the washer that goes between the pad and the caliper broke off and fell to the ground. There was enough of the rest of the washer still in place to be able to tighten the pad and get rolling. Looking at the left hand side pad, I noticed that the washer was completely missing on that side. Hmmm... |
 |
| Close up of the left hand side brake pad (on the rear). The washer is missing... |
 |
| Close up of the right hand side brake pad (Can't see the broken off piece of the washer because it's behind the caliper arm. The piece that broke off is about 25% of the washer). |
 |
| This is the front brake caliper for comparison. Both pads have their washers in place. |
 |
| Shimano casts in the model number for their major components. This is the front brake caliper and it says "BR-7800". The groupset on this bike is Dura-Ace 7800 (This is an older model series. I think the current generation Dura-Ace is in the 9000 series...). I'll order replacement pads for this series... |
 |
| Close up of the cast in model number. The iPhone doesn't do well with closeups... |
 |
| This is the pad missing the washer completely. |
Improved the sagging gate to the back yard
 |
| The gate post (attached to the wall of the house) is coming away from the wall. This causes the gate to interfere with the other half of the gate (that's stationary) and jam. |
 |
| Overview showing the gap between the gate post and the wall. It's about 1/2" or so at the top. |
 |
| Removed three long lag bolts to remove the gate post. |
 |
| This is the top bolt hole in the wall of the house. There's an expanding anchor but the hole is so damaged and enlarged that it doesn't grasp well. In order to improve it, I put several pieces of hard rubber hose material around the expanding anchor and the hole to take up the space so that when the bolt is installed and the metal expanding anchor spreads, it has something to compress against. (forgot to take a picture after filling the space...) |
 |
| This is the middle bolt hole. I had previously installed some plastic material to take up the gap between the anchor and the wall. This repair worked pretty well and does not need further changes. |
 |
| Same with this bottom hole as the middle hole. |
 |
| After reinstalling, the gap is down considerably. It's tight against the wall but there's gaps because the wall and the post are not even. Right now, it's about as tight against the wall as it can be. I will probably have to repair the top hole again soon. I'll either relocate the hole to a part of the wall or find a better way to fill the existing hole then reinstall a better anchor... |
Monday, April 20, 2020
fixing a loose hinge on one of the garage doors...
 |
| Of the left hand side doors, the upper hinge on the RH door is loose and is allowing the door to sag. |
 |
| These wood screws are loose (can't see the head due to all the paint on them). |
 |
| took off the paint so that they can be removed and replaced with longer screws. |
 |
| Bought these #14 x 3" wood screws at the local hardware store. |
 |
| Drilled holes for the longer screws before installing them. The one screw hole with no screw in it has a broken screw in the hole. I tired to drill out most of the old screw and tried to install a new longer screw but it broke. Oh well. I could drill it all out but by then the hole will probably end up being too big for a #14 screw... The other four longer screws went in straight and had good bite. The door no longer sags and when closing it, it no longer interferes with the other door & closes easily. Done. |
Water pressure regulator -- thinking about reducing the pressure...
 |
| This was replaced several years ago (the old one broke where it reduced the water pressure too much & could not be adjusted). The water pressure in the house is fine but it may be a little too high. According to the tag on the regulator, the output pressure adjustment range is 25 to 75 psi. I'm pretty sure that it's close to 75... The water pressure at the street (inlet pressure) is about 110 psi (a city worker checked it previously). |
Subscribe to:
Posts (Atom)